[streaming] Re: Stream DVB Channel: [ERROR/input1] Read error for program "Input DVB input1"

[Johann Soukup]

Hello Christoph

I ran yesterday exactly in the same problem that you described.

I even used the latest 0.4.0 drivers from the Metzler Bros.
homepage and still have the same problem. With the regular scan
tools of the libdvb package it seems to work fine and I can track
all Transponders and channels.

I changed the dvbrc exactly the way Damien described it
for the FEC value and there is also no "improvement"

I even tried to add the dvb channel to the vls.cfg

BEGIN "ntv"
  DeviceNumber  = ""                    # /dev/ost/dvr<i>

  Frequency     = "12670000"            # Frequency in kHz of the transponder
  Polarization  = "0"                   # 0 (vert) or 1 (horiz)
  SymbolRate    = "22000000"            # Symbol rate

  DiSEqC        = "0"                   # DiSEqC address of the used LNB
  LNB_Lof1      = "9750000"             # Local frequency of lower LNB band
  LNB_Lof2      = "10600000"            # Local frequency of upper LNB band
  LNB_SLof      = "11700000"            # Switch frequency of LNB
  SendMethod    = "1"                   # 0 - Send All Pids
                                        # 1 - Send only MPEG2 datas
END

and have also no changes.

Best Reagrds

 - Johann

Christoph Stotz schrieb:

> Hello,
>
> thank you for your reply. I tried it out, but actually it does not change
> anything.
>
> May I ask you which version of libdvb are you using and if the
> "satscan"-Utility is
> working for you ?
>
> If I run it, I get
>
> Error: ░⌡ ┐á⌠ ┐X⌡ ┐╝<á⌠ ┐↓É⌡ ┐░⌡ ┐ is not a valid keyword at
>
> Or worse..
>
> This stuff is driving me mad....
>
> Greetings,
>
> Christoph
>
> > -----Original Message-----
> > From: Damien Lucas [mailto:nitrox at via.ecp.fr]
> > Sent: Samstag, 14. Juni 2003 16:22
> > To: streaming at videolan.org
> > Cc: Christoph Stotz
> > Subject: Re: [streaming] Stream DVB Channel: [ERROR/input1]
> > Read error for program "Input DVB input1"
> >
> >
> > On Fri, Jun 13, 2003, Christoph Stotz wrote:
> > > TRANSPONDER ID 0012 SATID 0192 TYPE 0 FREQ 11836000 POL H
> > SRATE 27500000 FEC
> > > 3/4
> >
> > In the dvbrc file, FEC is described by a integer.
> > On the previous version of libdvb, (FEC 3/4) were described
> > by (3). So the
> > atoi() call was allright. Now, (FEC 3/4) is described by (4).
> >
> > so just get this line:
> >
> > TRANSPONDER ID 0012 SATID 0192 TYPE 0 FREQ 11836000 POL H
> > SRATE 27500000 FEC 4
> >
> > And it should work.
> >
> > By the way, you may not specify FEC. In that case, driver can
> > determine it by itself.
> >
> >
> > Best Regards,
> >
> > --
> > nitrox
> >
> --
> This is the streaming mailing-list, see http://www.videolan.org/streaming/
> To unsubscribe, please read http://www.videolan.org/support/lists.html
> If you are in trouble, please contact <postmaster at videolan.org>

--
----------------------------------------------------
 Netlantic GmbH          | phone +49 8122 222830-37
 Johann Soukup           | fax   +49 8122 222830-79
----------------------------------------------------
 Hallbergmooser Str. 5   |  http://www.netlantic.de
 D-85445 Schwaig/Munich  |  j.soukup at netlantic.de
----------------------------------------------------


-- 
This is the streaming mailing-list, see http://www.videolan.org/streaming/
To unsubscribe, please read http://www.videolan.org/support/lists.html
If you are in trouble, please contact <postmaster at videolan.org>